Showing posts with label inexpensive. Show all posts
Showing posts with label inexpensive. Show all posts

7/24/2012

Yamaha YSTSW012 8" Front-Firing Active Subwoofer, Black Review

Yamaha YSTSW012 8 Front-Firing Active Subwoofer, Black
Average Reviews:

(More customer reviews)
This is a great deal for $59 delivered. I don't know what I was expecting. Maybe some hollow sounding computer type sub-woofer that pops when I turn it on and off. This sub has a 50-watt RMS amp at 5ohm. It has a decent .5 inch MFD box with an internal space of almost 10.5 X 10.5 (small!) External is about 11.4 x 11.4 x 11.5 height. It's much better built than the Sony's on this site. They even made a small attempt to support the box with 1-inch corner braces on all 6 sides. The sub sounds great at lower volume. It maxis out fast though. In a small room or apartment, you wouldn't need it any louder. It's the quality of sound that's important, and that's where this delivers. Up to it's distortion point, it sounds like a true big sub-woofer. This is the perfect sub for anybody who is not allowed to shake the foundation. This sub plays deep! It just hits its max excursion fast. Either the amp is more than 50 watts or the speaker can't handle much wattage. Speaking of the speaker, it's about 5lbs. They seemed to have glued a smaller magnet onto the larger one at the base. I've heard of some seedy speaker manufactures doing this, but this speaker seems to deliver pretty good quality. I swapped out the stock speaker with a Dayton and secured the walls with cross braces and then covered the inside walls with carpet. Foam would take up to much space and there isn't much inside already. This setup was a pleasure to work with. The grill pops right off. The speaker is held on by 4 screws in the standard speaker hole location. (making it easy to replace) The amp is held on by 8 screws. The port is held in place mostly by a tight fit and some glue that easily breaks loose. The amp is connected to the speaker with standard removable connectors. That's it. It takes about 3-5 min to take apart. As for the Dayton, it performs about the same as the stock one. It was made for a little bit bigger box, but I wanted to know if the stock speaker was unable to handle much or was it the amp that produced the power. It seems to be the amp. It can push a stronger speaker. If I had a 100 watt 8" speaker with a high SPL, built for a small-ported box, and good excursion level (that's the amount of movement on a speaker), then I would really need the extra bracing. Problem is, that would cost much more than this whole system. That, and I wouldn't use a .5-inch thick box. Where am I going with this... anyway, this sub is worth every penny of $59. If you have a set of decent bookshelf speakers and a sub-woofer out jack on your amp that you're not using, you would be a fool not to get this. To cut costs, it has no auto on/off, and no pass through signal. If you must have auto on/off, buy a remote control on/off power supply from someplace cheap. I had one left over from my X-mass lights. (or use the power connection on the back of your receiver if you have one). This sub doesn't pop at all when turned on or off and its amp is inside the box. This sub is much better looking than a Sony I have. If the person before me didn't didn't give this 4 stars, I wouldn't have tested this out. So thanks! I'm very happy I purchased this. I think its so cheap people are afraid of it! I don't know how they make money on this. (update 1-11-08) to clarify the wattage on these: output power on the spec sheet is rated at 5ohms. 50 watts to 5 ohms RMS and 100 dynamic. It has a 6ohm speaker in it. That means it's probably pushing about 45 watts RMS to the speaker. The frequency response is -4db at 40hz, -10db at 30hz, -15db at 25hz. It has a decent flat response from 45hz to 120hz at 90db. It then tapers off to -5db at 200hz. Not bad for $59 !!! Update 1-15-07 Here's a FYI given to me: The second magnet glued on the back of the driver magnet is for shielding. It is not there to deceive. The second magnet is attached in polar opposite to the functional magnet, canceling the magnetic pollution it would normally give off. (Thanks Kevin!)

Click Here to see more reviews about: Yamaha YSTSW012 8" Front-Firing Active Subwoofer, Black



Buy NowGet 10% OFF

Click here for more information about Yamaha YSTSW012 8" Front-Firing Active Subwoofer, Black

Read More...

4/18/2012

Sony SS-CR3000 Center and Rear Channel Speaker Package Review

Sony SS-CR3000 Center and Rear Channel Speaker Package
Average Reviews:

(More customer reviews)
I'm a little chagrined I waited so long to immerse myself in the world of 5.1 surround sound.
Most websites on the subject will tell you to get all of your speakers from the same brand, so the harmonics are all cousins of each other. Well, with Bose bookshelf speakers, the accompanying surround speakers would have been another grand, so I decided to bottom end with Sony.
These little puppies are weird in that you can't take the mesh covers off to spock the look of the speaker diaphragms, but that's the only weird thing. They ship with the tiniest capellini-sized speaker wire you can imagine, which helps you enjoy your new sound straight out of the box until you can get some more decent sized wire.
For a starter kit, these are thoroughly sufficient, plus, they're sleek and unobtrusive. If you haven't experienced surround sound anywhere but the theaters, get these babies and rent Apocalypse Now, or any of the Bourne movies. (Or better yet, watch the dust storm episode from the first season of Carnivale--you'll quite literally be blown away.)
Also, you'll need a digital optical cable from your DVD player to your receiver; otherwise the Dolby surround won't work.

Click Here to see more reviews about: Sony SS-CR3000 Center and Rear Channel Speaker Package



Buy NowGet 30% OFF

Click here for more information about Sony SS-CR3000 Center and Rear Channel Speaker Package

Read More...

12/07/2011

Sony SSF-5000 Floor Standing 3-way Speaker (Pair) Review

Sony SSF-5000 Floor Standing 3-way Speaker (Pair)
Average Reviews:

(More customer reviews)
Forget all other audio companies. Sony will always have the highest quality products for the best prices. 3 foot high towers for $50 each??? They must be pretty mediocre right? Wrong. These speakers are wonderful.
They have a full, bright sound and can get as loud as you possibly want (and louder) if you have a decent receiver. There is a great distinction between the tweeter, mid and sub. These are the best speakers I have ever owned.
The only thing wrong with them is if you love extreme, rumbling bass, they might not meet your standards. But a good active sub woofer is a must for any good sound system anyway.

Click Here to see more reviews about: Sony SSF-5000 Floor Standing 3-way Speaker (Pair)

Fill a large room with the deep bass and pure treble of the SS-F5000 floor-standing speakers. Built to recreate tones across the entire range, these speakers elevate your music to a new high. The precision sound reproduction provides high resolution audio that you and your guests will appreciate from song to song.

Buy NowGet 38% OFF

Click here for more information about Sony SSF-5000 Floor Standing 3-way Speaker (Pair)

Read More...

11/12/2011

AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier Review

AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier
Average Reviews:

(More customer reviews)
I've owned one of these amps now for about six months. All the complaints I've read in the reviews have come from people who obviously can't be bothered to read, pay attention, or think things through. I'm specifically referring to Auto Input Switching/Power, lack of features, and output power.
First, this is NOT an integrated amp. Nor is it designed to be used primarily as a standalone system. It is intended to be used as a node on a distributed music system. The feature set for this unit has this use in mind.
It can function as a standalone unit but if you are going to use it as such you need to use it with a pre-amp or with an input source that provides adequate line in, input selection and the tone/equalization control you want.
Second, the auto input switching. The manual isn't clear on this and the feature can't be switched off, which is why I docked it a star. But some reading and thought will provide the solution. The auto input feature is only on input 1. If you run your primary input to input 2 you will have no problem with auto switching cutting off your music during quiet passages or after the track has started. If you need to use multiple sources without the auto switch cutting the input then you need to use external input switching (see pre-amp above) and make sure the switch/pre-amp is fed to input 2 on the amp.
Auto-power on issues: This feature can be turned on or off by way of a selector switch on the rear panel of the amp. Default is on. This is in the manual.
"It doesn't have a sub out": No, but it does have a line out/pass-through for input 2 which can be used for a sub out.
"It isn't loud enough": One of two things is happening here; 1. The line in isn't sufficient to properly drive the amp. 2. The speakers aren't efficient enough. If you are running speakers with less than 90db sensitivity you won't get decent performance from this or any other "low power" amp. I'm using Athena AS-B1.2's and I'm getting more than adequate volume and bass response. I recommend these (under $100 if you shop around) or the Athena AS-B2.2. Klipsch, Infinity, JBL, and Yamaha all make some nice bookshelf units with 90db sensitivity or better that would work nicely with this unit. Just because this is an inexpensive amp doesn't mean you can get away with cheap speakers.
"There isn't enough bass": 1. Make sure the source is providing enough bass input. If the source doesn't have a tone control for bass you may need to use a pre-amp. 2. Use better speakers. When I first got my amp the speakers I had ordered for it were delayed, so I used some old early 80's bookshelf speakers to test the amp out.
Those speakers had no bass at all, or treble, or much midrange. Basically it sounded like an AM pocket radio. When the Athenas came in and were properly broken in the sound improved greatly. It also helps to have the speakers placed properly. If your speakers are rear vented they don't need to be in an enclosed space or pushed up against a wall (I see this all the time, even on store displays).
My experiences with this Amp: I ordered this amp with a pair of Athena AS-B1.2 bookshelf speakers for use in my home office. Inputs are from my PC (by USB DAC) and an iPod dock. Both inputs run through an audio switch to input 2 on the amp. The files played through it are a mix of OGG, FLAC, AAC, ALAC, WAV, and MP3. Mostly FLAC.
I was impressed by the fit and finish of the unit out of the box. I've seen many allegedly high end products that don't have this level of finish (Cameras, turntables, TV, PC Cases, Cars, etc.). The weight is substantial. As near as I can tell by looking through the vent slots the transformer takes up at least half the case. The power lines in my house aren't very clean and I have hum issues with most A/V equipment I own, but I have yet to hear any hum (in normal conditions) from this amp when turned all the way up, even when it's been plugged into outlets that give other equipment fits. The only way to get hum is to touch an input with a finger. In normal use the background is dead silent. Good power supply.
The design is minimalist and clean. The only panel controls are power, speakers, volume and balance. It is low profile and unobtrusive and gives off very little heat, even when left on (with the volume turned down). Mine doubles as a monitor stand, LCDs only.
There are two inputs but they are auto switched. The first input is the auto switch input, as stated above. This means that if an input is detected it will switch to input 1 over input 2. It is fairly sensitive and will switch back and forth during pauses or quieter passages in the music. If you listen to a lot of Jazz, classical, or chamber music with pauses and quiet bits you will definitely want to use input 2 to prevent it from dropping out during those passages.
There is an autopower feature as well. If left on it will cause the same problems with the amp cutting out during quiet passages as the autoinput switching. However it can be disabled by a selector switch on the back of the unit. This is clearly explained in the manual. The intent is to allow the unit to be powered on remotely when used with a distributed music system. If you want a standalone system disable this feature and turn it on and off manually.
The sound is deep and rich with excellent separation, depth, and imaging. There's plenty of bass for most of what I listen too (Jazz, folk, and classic rock), and outstanding midrange. Treble does seem to roll off a bit, but that may be the speakers. Volume is more than enough to shake the walls and floor of my office and the music can be heard clearly throughout the second floor of the house. Personally I think it's more than loud enough to use as a primary system if you have a smallish living room (but with larger speakers). I haven't heard any distortion at loud volumes, but excessive line in might change that. More importantly to me the sound doesn't get muddy at low volume levels. It remains clear and detailed. I have no problem listening to most of my collection for hours on end with this amp while I work, or kicking back on the office sofa with some whiskey.
Most of my music files on the PC are lossless, but I do have a few dogs among the MP3 and WAV files. It's no great feat for an amp to sound good with a lossless file so I ran a few of the nastier files through it to see how it did. For the most part it took the edginess off most of the rougher files and made them almost pleasant to listen to. There are a few bad tracks that are best left to regular PC speakers, and a few FLAC files ripped from CD where bad mastering shows up more clearly now. Win some, loose some.
Nitpicks: My amp pops when turned on and off, which has the potential to damage speakers. It's not loud, but I turn the volume down before I hit the switch. I would prefer a manual input switch. Price has changed by as much as $30 on Amazon over a relatively short time.
Before buying this I listened to a friend's office setup with a Super T-Amp and a pair of Infinity Bookshelf speakers. To my ears the Amp100 sounds just as nice at lower volumes plus it can pack more of a punch when called for. It's not as compact as the Super-T or as stylish, but it fills my needs.

Click Here to see more reviews about: AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier

50 Watt Power Amplifier for multiple Custom Home Audio Distribution and Home Theater Applications. Ideal for use as aremote amplifer, A single zone amplifier, or rear channel amplifier for Dolby 6.1 / 7.1 systems.

Buy NowGet 46% OFF

Click here for more information about AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier

Read More...

11/05/2011

Pyle Home PCA1 Mini 2 x 15-Watt Stereo Power Amplifier Review

Pyle Home PCA1 Mini 2 x 15-Watt Stereo Power Amplifier
Average Reviews:

(More customer reviews)
I bought this amplifier to replace the stereo/amplifier combo unit in an old mini system, which was starting to give up on me. For the size and price, I wasn't expecting very much, but I figured I do most of my listening at fairly low levels and a mere 15 watts wouldn't be a big handicap. I figured it was worth a try for the price.
Wow, were my doubts misplaced. When you pick this tiny amplifier up, any questions about its quality immediately disappear. Despite its unimpressive size, it weighs a hefty two or three pounds. Made of solid metal, it's got fairly high-quality connectors on the back (no fancy 5-way binding posts, though) and everything has a very smooth, solid, substantial feel.
The low power rating isn't an issue either, especially if you're comparing to typical department-store stereo equipment, because the ratings on those systems are usually complete fabrications. In fact, if you've got a typical set of 8-ohm bookshelf speakers, this amp should be able to run them dangerously loud before you start to notice any distortion. The frequency response also seems good; it's definitely better than the response for the speakers I have it hooked up to right now, so I can't really comment on the limits.
I'm not sure how well this would work for larger speakers or those with more than two or three drivers, and I'm not sure how well it handles 4-ohm speakers. However, even for moderately large 8-ohm bookshelf units, I can't see a single flaw.

Click Here to see more reviews about: Pyle Home PCA1 Mini 2 x 15-Watt Stereo Power Amplifier



Buy NowGet 66% OFF

Click here for more information about Pyle Home PCA1 Mini 2 x 15-Watt Stereo Power Amplifier

Read More...