Showing posts with label audiosource. Show all posts
Showing posts with label audiosource. Show all posts

7/24/2012

AudioSource Amp 5.1A 100-Watt Monoblock Power Amplifier Review

AudioSource Amp 5.1A 100-Watt Monoblock Power Amplifier
Average Reviews:

(More customer reviews)
AudioSource is well known for providing good value for the price and they don't dissapoint with their 5-series amps. There's nothing in its price-range that has similar quality.
The output isn't quite as rich a Bruce Moore 70, but at 1/20th the price, it's a great deal.

Click Here to see more reviews about: AudioSource Amp 5.1A 100-Watt Monoblock Power Amplifier

The Amp 5.1 stereo power amplifier from AudioSource is a powerful and flexible addition to your home theater. You can use this monoblock amplifier by itself, or combine it with a series of Amp 5.1 units to power an entire home theater and drive speakers throughout your home.
The clean design houses a high-power amplifier that is easy to set up and easy to expand as your home theater grows. AudioSource amplifiers deliver accurate, rich sound, combining high sound-pressure levels and a clear reproduction of even the most subtle details of sound. The Amp 5.1 provides up to 100 watts per channel with total harmonic distortion of less than 0.1%.
Depending on your needs, you can place and replace several monoblock amps in one system. It's easy to connect power sources, audio and video inputs, and speaker outputs with the expansion-friendly design. Balanced inputs allow the Amp 5.1 to connect to audio and video components with XLR outputs, and unbalanced inputs handle RCA output connections.
The front panel of the amplifier has a simple array of LED displays that signal both operating status and potential warnings. A protect warning helps you avoid overloading or overheating the unit, and it will reset the unit to the initial settings once the problem is addressed.
A phase control button allows you to switch the polarity of the speaker outputs to compensate for occasions where speakers are out of phase and sounding hollow. A low-cut control feature filters the lowest frequencies from your small speakers, preventing distortion and protecting the speakers. In the heart of the amp, the torodial power transformer generates a big sound while reducing distortion by shielding the sound from stray magnetic fields. You can control the volume directly on the unit or by adjusting the signal source component (such as your receiver, preamp, etc.).
What's in the Box Amp 5.1 stereo amplifier and owne'rs manual.

Buy Now

Click here for more information about AudioSource Amp 5.1A 100-Watt Monoblock Power Amplifier

Read More...

11/12/2011

AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier Review

AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier
Average Reviews:

(More customer reviews)
I've owned one of these amps now for about six months. All the complaints I've read in the reviews have come from people who obviously can't be bothered to read, pay attention, or think things through. I'm specifically referring to Auto Input Switching/Power, lack of features, and output power.
First, this is NOT an integrated amp. Nor is it designed to be used primarily as a standalone system. It is intended to be used as a node on a distributed music system. The feature set for this unit has this use in mind.
It can function as a standalone unit but if you are going to use it as such you need to use it with a pre-amp or with an input source that provides adequate line in, input selection and the tone/equalization control you want.
Second, the auto input switching. The manual isn't clear on this and the feature can't be switched off, which is why I docked it a star. But some reading and thought will provide the solution. The auto input feature is only on input 1. If you run your primary input to input 2 you will have no problem with auto switching cutting off your music during quiet passages or after the track has started. If you need to use multiple sources without the auto switch cutting the input then you need to use external input switching (see pre-amp above) and make sure the switch/pre-amp is fed to input 2 on the amp.
Auto-power on issues: This feature can be turned on or off by way of a selector switch on the rear panel of the amp. Default is on. This is in the manual.
"It doesn't have a sub out": No, but it does have a line out/pass-through for input 2 which can be used for a sub out.
"It isn't loud enough": One of two things is happening here; 1. The line in isn't sufficient to properly drive the amp. 2. The speakers aren't efficient enough. If you are running speakers with less than 90db sensitivity you won't get decent performance from this or any other "low power" amp. I'm using Athena AS-B1.2's and I'm getting more than adequate volume and bass response. I recommend these (under $100 if you shop around) or the Athena AS-B2.2. Klipsch, Infinity, JBL, and Yamaha all make some nice bookshelf units with 90db sensitivity or better that would work nicely with this unit. Just because this is an inexpensive amp doesn't mean you can get away with cheap speakers.
"There isn't enough bass": 1. Make sure the source is providing enough bass input. If the source doesn't have a tone control for bass you may need to use a pre-amp. 2. Use better speakers. When I first got my amp the speakers I had ordered for it were delayed, so I used some old early 80's bookshelf speakers to test the amp out.
Those speakers had no bass at all, or treble, or much midrange. Basically it sounded like an AM pocket radio. When the Athenas came in and were properly broken in the sound improved greatly. It also helps to have the speakers placed properly. If your speakers are rear vented they don't need to be in an enclosed space or pushed up against a wall (I see this all the time, even on store displays).
My experiences with this Amp: I ordered this amp with a pair of Athena AS-B1.2 bookshelf speakers for use in my home office. Inputs are from my PC (by USB DAC) and an iPod dock. Both inputs run through an audio switch to input 2 on the amp. The files played through it are a mix of OGG, FLAC, AAC, ALAC, WAV, and MP3. Mostly FLAC.
I was impressed by the fit and finish of the unit out of the box. I've seen many allegedly high end products that don't have this level of finish (Cameras, turntables, TV, PC Cases, Cars, etc.). The weight is substantial. As near as I can tell by looking through the vent slots the transformer takes up at least half the case. The power lines in my house aren't very clean and I have hum issues with most A/V equipment I own, but I have yet to hear any hum (in normal conditions) from this amp when turned all the way up, even when it's been plugged into outlets that give other equipment fits. The only way to get hum is to touch an input with a finger. In normal use the background is dead silent. Good power supply.
The design is minimalist and clean. The only panel controls are power, speakers, volume and balance. It is low profile and unobtrusive and gives off very little heat, even when left on (with the volume turned down). Mine doubles as a monitor stand, LCDs only.
There are two inputs but they are auto switched. The first input is the auto switch input, as stated above. This means that if an input is detected it will switch to input 1 over input 2. It is fairly sensitive and will switch back and forth during pauses or quieter passages in the music. If you listen to a lot of Jazz, classical, or chamber music with pauses and quiet bits you will definitely want to use input 2 to prevent it from dropping out during those passages.
There is an autopower feature as well. If left on it will cause the same problems with the amp cutting out during quiet passages as the autoinput switching. However it can be disabled by a selector switch on the back of the unit. This is clearly explained in the manual. The intent is to allow the unit to be powered on remotely when used with a distributed music system. If you want a standalone system disable this feature and turn it on and off manually.
The sound is deep and rich with excellent separation, depth, and imaging. There's plenty of bass for most of what I listen too (Jazz, folk, and classic rock), and outstanding midrange. Treble does seem to roll off a bit, but that may be the speakers. Volume is more than enough to shake the walls and floor of my office and the music can be heard clearly throughout the second floor of the house. Personally I think it's more than loud enough to use as a primary system if you have a smallish living room (but with larger speakers). I haven't heard any distortion at loud volumes, but excessive line in might change that. More importantly to me the sound doesn't get muddy at low volume levels. It remains clear and detailed. I have no problem listening to most of my collection for hours on end with this amp while I work, or kicking back on the office sofa with some whiskey.
Most of my music files on the PC are lossless, but I do have a few dogs among the MP3 and WAV files. It's no great feat for an amp to sound good with a lossless file so I ran a few of the nastier files through it to see how it did. For the most part it took the edginess off most of the rougher files and made them almost pleasant to listen to. There are a few bad tracks that are best left to regular PC speakers, and a few FLAC files ripped from CD where bad mastering shows up more clearly now. Win some, loose some.
Nitpicks: My amp pops when turned on and off, which has the potential to damage speakers. It's not loud, but I turn the volume down before I hit the switch. I would prefer a manual input switch. Price has changed by as much as $30 on Amazon over a relatively short time.
Before buying this I listened to a friend's office setup with a Super T-Amp and a pair of Infinity Bookshelf speakers. To my ears the Amp100 sounds just as nice at lower volumes plus it can pack more of a punch when called for. It's not as compact as the Super-T or as stylish, but it fills my needs.

Click Here to see more reviews about: AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier

50 Watt Power Amplifier for multiple Custom Home Audio Distribution and Home Theater Applications. Ideal for use as aremote amplifer, A single zone amplifier, or rear channel amplifier for Dolby 6.1 / 7.1 systems.

Buy NowGet 46% OFF

Click here for more information about AudioSource AMP-100 2-Channel Bridgeable Stereo Power Amplifier

Read More...

7/22/2011

Sherwood RX-4105 2-Channel 100-Watt Stereo Receiver Review

Sherwood RX-4105 2-Channel 100-Watt Stereo Receiver
Average Reviews:

(More customer reviews)
This Sherwood (noted brand years ago, now mysterious) might be a decent bargain for twice the money. It's stripped down by present standards -- two channels only, no phonograph input. It's dead quiet and extremely clean sounding. I can't hear any emphases or dead spots in the frequencies. The tuner is exceptionally good; I am surprised at the success I'm having with it in a poor reception area, with only the antennas that are supplied. Appearance and quality are fine: nice black steel case, solid buttons, one big old volume knob. It was all I needed, so I'm very pleased. Going to get another for a computer amp.

Click Here to see more reviews about: Sherwood RX-4105 2-Channel 100-Watt Stereo Receiver

Sherwood's incredibly affordable RX-4105 offers integrated preamplification and amplification, inputs for numerous audio source components, and advanced radio tuning and station access. The receiver delivers 100 watts RMS per channel x 2 for strong, clear sound across the audible spectrum--even at low listening levels. The company has lowered the amplifier's distortion relative to the previous model (the RX-4105), to less than 0.08 percent, while also giving the receiver a new layout borrowed from its higher-end components.The RX-4105 uses totally discrete amplifiers for all channels (TDAS) to maintain its high power and low distortion. Use the receiver's A and B clip-type speaker outputs to power 2 different rooms, or to biwire a pair of speakers for more efficient amplification (with A outputs driving the woofers, for instance, and the B outputs driving the tweeters--make sure your speakers are compatible if this is a key feature for you).The receiver also offers a handy 25-key remote control and switching for 2 pair of loudspeakers. Audio inputs switch between and amplify up to 4 additional components, including 2 requiring both inputs and outputs (such as a cassette deck and a VCR). The built-in AM/FM tuner features 30 station presets and auto station setup.Other features include bass and treble tone controls, a dimmable fluorescent display, and a .25-inch headphone jack for private listening.What's in the Box Sherwood RX-4105 receiver, remote control, AC power supply cord, FM indoor antenna, AM loop antenna set, and owner's manual.

Buy NowGet 40% OFF

Click here for more information about Sherwood RX-4105 2-Channel 100-Watt Stereo Receiver

Read More...